PULS
Power supply 3-phase, 48 V dc Dimension X Series
Dimension X series is a series of semi-regulated power supplies. A so-called semi-controlled unit means that the output voltage is regulated within the specified input voltage range. Outside this range decreases / increases the output voltage compared to the input voltage.
The unit has a bonus effect of 25% (25 A) to cope with high starting currents, as well as a very high short-circuit current enables safe trips for eg MCB. The unit leaves up to 90 A at 100 ms. Lasts short circuit longer than 100 ms, the unit shuts off automatically. See chart below for details. Recovery occurs in the front, or by disconnecting the primary voltage.
A yellow LED indicates the status and warns of the following errors; phase failure, over-temperature and high load current.
The unit has a low weight (1.4 kg), no inrush current and active transient filter that protects the secondary side from transients on the primary side.
Typical applications include motors, solenoids or other "power hungry" loads that do not have requirements for accurate voltage regulation. X series are a great alternative to traditional transformers. With lower energy costs and easier installation, along with an attractive price concept means a low total cost.
We recommend free space of 40 mm above and 20 mm under the power supply, and 5 mm at the sides. (if neighbouring products are counted as a heat source spacing of 15 mm is recommended).
Input voltage range/regulation |
|
Output characteristics |
|
- Output current of 20 A
- Up to 96% efficiency
- Semi Regulated
- Replaces linear transformers
- Very high short-circuit current
Selected variant
Specifications
| Number of phases | 3 |
|---|---|
| Input voltage AC | 400 V |
| Input voltage ac min | 360 V AC |
| Input voltage ac max | 440 V AC |
| Inrush current at 400 V ac typical | 4 A |
| Power Factor at 400 V AC, full load. Typical | 0,93 |
| Supply Frequency | 50-60 ±6 % |
| Power consumption at 400 V ac | 1,65 A |
| Type Power Supply | AC-DC |
| Output voltage | 48 V DC |
| Output voltage min | 48 V DC |
| Output voltage max | 48 V DC |
| Output Current | 20 A |
| Effect | 960 W |
| Power Reduction Of 60 To 70 ° C | 24 W/°C |
| Ripple. max | 300 mV pp |
| Temperature Range Without Derating From | -25 °C |
|---|---|
| Temperature Range Without Derating To | 60 °C |
| Efficiency At 400 V AC, full load. Typical | 96 % |
| Lifetime at 400 V ac, full load and +40 ° C | 77000 h |
| MTBF (IEC 61709) 400 V ac, max loan, +40 °C | 541000 h |
| Width | 96 mm |
| Height | 124 mm |
| Depth | 159 mm |
| Weight | 1,4 kg |
| Series | Dimension X |
| Approvals | CB, CE, CSA, UL |
| Material Protection | Aluminium |
| Hold-up time at 400 V AC, full load. Typical. | 3 ms |
| IP Class | IP20 |
| Active Transient | Yes |
Product description
Dimension X series is a series of semi-regulated power supplies. A so-called semi-controlled unit means that the output voltage is regulated within the specified input voltage range. Outside this range decreases / increases the output voltage compared to the input voltage.
The unit has a bonus effect of 25% (25 A) to cope with high starting currents, as well as a very high short-circuit current enables safe trips for eg MCB. The unit leaves up to 90 A at 100 ms. Lasts short circuit longer than 100 ms, the unit shuts off automatically. See chart below for details. Recovery occurs in the front, or by disconnecting the primary voltage.
A yellow LED indicates the status and warns of the following errors; phase failure, over-temperature and high load current.
The unit has a low weight (1.4 kg), no inrush current and active transient filter that protects the secondary side from transients on the primary side.
Typical applications include motors, solenoids or other "power hungry" loads that do not have requirements for accurate voltage regulation. X series are a great alternative to traditional transformers. With lower energy costs and easier installation, along with an attractive price concept means a low total cost.
We recommend free space of 40 mm above and 20 mm under the power supply, and 5 mm at the sides. (if neighbouring products are counted as a heat source spacing of 15 mm is recommended).
Input voltage range/regulation |
|
Output characteristics |
|
Related
Fiepos — The power supply of the future
The need for flexible, modular systems shapes machine and system engineering. Decentralization of the system components has proven to be an important factor for success.
The recognized Puls quality for an attractive price
The PIANO PIC series is designed for applications that require reliable DIN rail power supplies, which are focused to deliver the most widely required customer functionalities. Our PIC units offer this simplicity without making compromises on PULS’ renowned qualities; efficiency, service lifetime, reliability and size.
Redundant systems without redundancy modules
With the CP series, PULS offers a unique feature: Power supplies with an integrated decoupling function based on efficient MOSFET technology. This means there is no need for additional redundancy modules in 1+1 and n+1 redundant systems.
Push-In sockets that save both time and space
ComatReleco has launched a new series of push-in sockets specifically designed for time and space savings.
New “all-round” Syr-Line time relays by Crouzet
Crouzet has honoured the strong Syrelec time relay traditions established in the 1980s, first by Cronos and Cronos 2 series. Now, Crouzet presents the compact and extremely versatile Syr-Line series.
New WADI cable gland series from Jacob
The new WADI product family by Jacob features a completely redesigned gland rubber, which allows extensive sealing and tightening area.
